Showing 12 results for Tial
S.r. Allahkaram, R. Shamani,
Volume 6, Issue 1 (3-2009)
Abstract
Abstract: Due to the expansion of high voltage Alternating Current (AC) power transmission lines and cathodically
protected buried pipelines, it is becoming more and more difficult to construct them with enough safe distances
between them. Thus, the pipelines are frequently exposed to induced AC interferences, which result in perturbation of
Cathodic Protection (CP) due to AC corrosion. To study the above criterion, an experimental set up was used with
coupons exposed to simulated soil solutions, while under both CP and AC induced condition for which an AC+DC
power supply was utilized. The experiments were carried out in several simulated soil solutions corresponding to
several soil samples collected from various regions along a buried pipeline with overhead parallel high voltage power
transmission line. The results indicated that AC corrosion depends strongly on the composition of the soil.
S.r. Allahkaram, R. Shamani,
Volume 6, Issue 2 (6-2009)
Abstract
Abstract: The risks of alternating current (AC) corrosion and overprotection increasingly demand new criteria for
cathodically protected pipelines. To assess the risk of AC corrosion, new cathodic protection (CP) criteria have been
proposed based on DC/AC current densities measurements using coupons. The monitoring system designed for this
project was based on the instant-off method, with steel coupons simulating coating defects on a buried pipeline. The
problems associated with the instantaneous off-potential measurements have been attributed to a non-sufficient time
resolution. In present study, it has been possible to determine the de-polarisation of steel coupon within a few
milliseconds after disconnecting the coupon from the DC/AC power source, by increasing data acquisition rate. For
this, a monitoring system was developed in order to measure the IR-free potential together with the DC/AC current
densities. The monitoring system was utilized for both laboratory experiments and site survey to study the mechanism
and the condition of AC corrosion, its mitigation and more importantly to define new CP criteria.
R. Khoshhal, M. Soltanieh, M. Mirjalili,
Volume 7, Issue 1 (3-2010)
Abstract
Abstract:
titanium sheets in pure molten aluminum at 750
and X-Ray Diffraction Analysis results, TiAl
intermetallic layer thickness increases slowly at primary stages. After that an enhanced growth rate occurs due to layer
cracking and disruption. Presumably, reaction starts with solving titanium into the molten aluminum causing in
titanium super saturation and TiAl
intermetallic layer which consequently leads to TiAl
energy of intermetallic layer formation and growth was developed by measuring titanium thickness decreases.
In this work, kinetics of intermetallic compounds formation in Al-Ti system was studied by immersingoC, 850 oC and 950 oC. According to Scanning Electron Microscopy3 is the only phase can form at the interface. Observations revealed that3 formation. At this stage, growth may be controlled by aluminum diffusion through3 formation at the interface of Ti-TiAl3. Furthermore, activation
Mrs Somaye Alamolhoda, Dr Saeed Heshmati-Manesh, Dr Abolghasem Ataie,
Volume 7, Issue 3 (8-2010)
Abstract
In this research an ultra-fine grained composite structure consisting of an intermetallic matrix together with dispersed nano-sized Al2O3 obtained via mechanical activation of TiO2 and Al in a high energy ball mill and sintering of consolidated samples. Phase composition and morphology of the milled and sintered samples were evaluated by XRD and SEM techniques Thermal behavior of the powder sample milled for 8 hours was evaluated by DTA technique. DTA results showed that, the reaction happens in two steps. The first step is the aluminothermic reduction of TiO2 with Al. XRD observations reveals that minor amount of Ti3Al phase formed during reduction reaction together with TiAl and Al2O3 major phases. This intermetallic phase disappeared when sintering temperature was increased to 850 ºC. The second step in DTA is related to a reaction between residual Al in the system (partly dissolved in TiAl lattice) and the Ti3Al phase produced earlier at lower temperatures. SEM micrographs reveal that by completion of the reduction reaction more homogeneous and finer microstructure is observable in sintered samples.
S. Ghafurian, S. H. Seyedein, M. R. Aboutalebi, M. Reza Afshar,
Volume 8, Issue 3 (9-2011)
Abstract
Abstract: Microwave processing is one of the novel methods for combustion synthesis of intermetallic compounds and
composites. This method brings about a lot of opportunities for processing of uniquely characterized materials. In this
study, the combustion synthesis of TiAl/Al2O3 composite via microwave heating has been investigated by the
development of a heat transfer model including a microwave heating source term. The model was tested and verified
by experiments available in the literature. Parametric studies were carried out by the model to evaluate the effects of
such parameters as input power, sample aspect ratio, and porosity on the rate of process. The results showed that
higher input powers and sample volumes, as well as the use of bigger susceptors made the reaction enhanced. It was
also shown that a decrease in the porosity and aspect ratio of sample leads to the enhancement of the process.
F Foadian, M Soltanieh, M Adeli, M Etminanbakhsh,
Volume 11, Issue 4 (12-2014)
Abstract
Metallic-intermetallic laminate (MIL) composites are promising materials for structural applications especially in the aerospace industry. One of the interesting laminate composites is the Ti-TiAl 3 multilayer. In this work, commercially pure sheets of aluminum and titanium with almost equal thickness of around 0.5 mm were explosively joined. The achieved multilayers were annealed at 630 ℃in different times so that an intermetallic layer was formed at the Ti/Al interface. The resulting microstructure was studied by optical and scanning electron microscopy and Energy Dispersive Spectroscopy (EDS). TiAl3 was the only intermetallic phase that was observed in all annealing times. The kinetics of the formation of TiAl 3 was investigated and compared to previous research studies performed on Ti-Al multilayers which were fabricated using methods other than explosive welding.
M.h. Avazkonandeh-Gharavo, M. . Haddad-Sabzevar, H. Fredriksson,
Volume 13, Issue 2 (6-2016)
Abstract
Because the partition coefficient is one of the most important parameters affecting microsegregation, the aim of this research is to experimentally analyse the partition coefficient in Al-Mg alloys. In order to experimentally measure the partition coefficient, a series of quenching experiments during solidification were carried out. For this purpose binary Al-Mg alloys containing 6.7 and 10.2 wt-% Mg were melted and solidified in a DTA furnace capable of quenching samples during solidification. Cooling rates of 0.5 and 5 K/min were used and samples were quenched from predetermined temperatures during solidification. The fractions and compositions of the phases were measured by quantitative metallography and SEM/EDX analyses, respectively. These results were used to measure the experimental partition coefficients. The resultant partition coefficients were used to model the concentration profile in the primary phase and the results were compared with equilibrium calculations and experimental profiles. The results of calculations based on the experimental partition coefficients show better consistency with experimental concentration profiles than the equilibrium calculations.
Y. Dewang, M.s. Hora, S.k. Panthi,
Volume 14, Issue 4 (12-2017)
Abstract
Finite element simulation of stretch flanging process was carried out in order to investigate the effect of process parameters on maximum thinning (%) in stretch flanging process. Influences of initial flange length, punch die clearance, width of sheet metal blank and blank holding force were investigated on maximum thinning (%). Finite element simulation was done using FEM software package ABAQUS. Sheet metal blanks of AA 5052 were utilized for numerical simulation of stretch flanging process. Mesh convergence study was carried out to ascertain the accuracy of present FEM model. It is found that circumferential strain and shell thickness decreases with decrease in initial flange length and punch-die clearance while both decreases with increase in blank-holding force. Radial strain increases with decrease in initial flange length and punch-die clearance and with increment in blank-holding force and width of sheet. It is found that width of sheet metal blank and blank holding force have greater influence on maximum thinning (%) as compared to initial flange length and punch die clearance.
Jaouad Zerhouni, Fouzia Rhazi Filali, Mohammed Naciri Bennani, Omar Qabaqous, Aziz Bouymajane, Jamal Houssaini, Safae Allaoui, Faouzia Benhallam,
Volume 18, Issue 4 (12-2021)
Abstract
Our study is to highlight the effect of the acid-base character and the redox potential of two clays, synthetic anionic Layered Double Hydroxides Zn3Al-CO3 (LDH) clay, and natural commercial cationic clay "Ghassoul" on their antioxidant and antibacterial activities. The antibacterial effect was tested on two Gram-positive bacteria: Staphylococcus aureus and Enterococcus faecalis. Then it was tested on a Gram-negative bacterium: Escherichia coli. The determination of the minimum inhibitory concentration of the two materials was carried out using the microplatemicrotitration technique. The antioxidant activities of clays are assessed by the methods 2.2-diphenyl-1-picrylhydrazyl and the reducing power of iron (Fe3+). The redox potential (Eh) was measured and the redox strength (rH2) was evaluated. The results showed that these materials have an antibacterial effect on the three bacteria tested, the measured zero charge point of Ghassoul (pHzpc =8.75) more basic than that of double layer hydroxide (pHzpc =7.5), redox potential of LDH (-27mV) was higher than that of Gh (- 103mV), and the rH2 of Gh (14.04) was higher compared to anionic clay (13.33).
Keywords: LDHs, Ghassoul, Redox Potential, Zero point of Charge, Antibacterial.
Lakache Houssem Eddine, Badji Riad, May Abdelghani,
Volume 20, Issue 3 (9-2023)
Abstract
The objective underlined in this work is to apply Rotary Friction Welding (RFW) process to joint similar AA2024 and TiAl6V4 welds. The experiment is conducted by varying the input parameters (rotational speed, friction pressure and friction time) using Taguchi’s L9 orthogonal array method. MINITAB software was used to plot the response chart. The output parameter considered in this approach is the Ultimate Tensile Strength (UTS) of the weld joint, where the optimum RFW condition for maximizing the UTS were determined. Besides, the most influential process parameter has been determined using statistical analysis of variance (ANOVA). Finally, the general regression equations of the UTS for both materials are formulated and confirmed by means of the experimental tests values.
Faraz Hussain, Muhammad Umar Manzoor, Muhammad Kamran, Tahir Ahmad, Fahad Riaz, Sehrish Mukhtar, Hafiz Muhammad Rehan Tariq, Muhammad Ishtiaq,
Volume 21, Issue 3 (9-2024)
Abstract
Magnesium alloys are increasingly valued for biomedical applications due to their biocompatibility. This study investigates Mg-AZ31B alloy samples treated with quartz and alumina grits (<200 μm) at varied pressures, followed by anodization in an eco-friendly alkaline electrolyte. The results show that increased blasting pressure produces a rougher surface. Anodization time significantly affects the thickness of the anodic film, leading to a transition in surface morphology from fine to coarse structures with complete film coverage. Characterization by XRD reveals that the anodic film mainly comprises magnesium oxide and hydroxide phases. Open Circuit Potential (OCP) measurements demonstrate enhanced corrosion resistance post-anodization, particularly notable at 40 minutes on alumina-blasted samples. ANOVA confirms that both blasting pressure and anodization time significantly influence coating thickness and OCP, indicating the formation of a dense anodized layer.
Bakhrom Abdulazizov,
Volume 21, Issue 4 (12-2024)
Abstract
In this work, the effect of variation of the non-ideality coefficient of the p-n-junction volt-ampere (I-V) characteristic located in the strong microwave field on the differential resistance, diffusion capacitance and differential conductance is studied. Here, it is shown that the p-n junction I-V characteristics increases with the value of the non-ideality coefficient, whether the differential resistance is in a strong microwave field or a weak microwave field. Diffusion capacitance and differential conductance are shown to decrease with increasing value of non-ideality coefficient.
