Showing 7 results for Hot Deformation
Abbasi S.m., Shokouh Far A., Ehsani N.,
Volume 3, Issue 3 (12-2006)
Abstract
In this study the hot deformation behaviour of a precipitation hardened (PH) stainless steel at high strain rates has been predicted through hot compression testing. Stress-strain curves were obtained for a range of strain rates from 10-3 to 10+1 S-1 and temperatures from 850 to 1150°C. Results obtained by microstructure and stress-strain curves show that at low temperatures and high strain rates, where the Zener-Holman parameter (Z) is high, work hardening and dynamic recovery occure. By increasing temperature and decreasing strain rate, the Z parameter is decreased, so that dynamic recrystallization is the dominant softening mechanism. The results were fitted using a Log Z versus Log (sinh (a sp) diagram allowing an assessment of the behavior of the stresses measured at strain rates closer to those related to the industrial hot rolling schedules. It is clearly shown that the data collected from low strain rate testing can be fairly reasonably extrapolated to higher orders of magnitude of strain rate.
E. Badami, M. T. Salehi, S. H. Seyedein,
Volume 11, Issue 4 (12-2014)
Abstract
Hot deformation behavior of a medium Cr/Mn Al6061 aluminum alloy was studied by isothermal compression test at temperatures range of 320 to 480 °C and strain rates range of 0.001 to 0.1 s −1. The true stresstrue strain curves were analyzed to characterize the flow stress of Al6061. Plastic behavior, as a function of both temperature and strain rate for Al6061, was also modeled using a hyperbolic sinusoidal type equation. For different values of material constant α in the range of 0.001 to 0.4, values of A, n and Q were calculated based on mathematical relationships. The best data fit with minimum error was applied to define constitutive equation for the alloy. The predicted results of the proposed model were found to be in reasonable agreement with the experimental results, which could be used to predict the required deformation forces in hot deformation processes
M. Rakhshkhorshid,
Volume 13, Issue 3 (9-2016)
Abstract
Till now, different constitutive models have been applied to model the hot deformation flow curves of different materials. In this research, the hot deformation flow stress of API X65 pipeline steel was modeled using the power law equation with strain dependent constants. The results was compared with the results of the other previously examined constitutive equations including the Arrhenius equation, the equation with the peak stress, peak strain and four constants and the equation developed based on a power function of Zener-Hollomon parameter and a third order polynomial function of strain power a constant number. Root mean square error (RMSE) criterion was used to assess the performance of the understudied models. It was observed that the power law equation with strain dependent constants has a better performance (lower RMSE) than that of the other understudied constitutive equations except for the equation with the peak stress, peak strain and four constants. The overall results can be used for the mathematical simulation of hot deformation processes
M. Sadeghi, M. Hadi, O. Bayat, H. Karimi,
Volume 17, Issue 1 (3-2020)
Abstract
In this paper a constitutive equation was considered for the isothermal hot compression test of the Mn-Ni-Cr alloy. The hot compression test was performed in the strain rate range of 0.001-0.1 s-1 and deformation temperature was varied from 700 to 900 °C. A considerable reduction in flow stress was observed regardless of the strain rate when temperature was increased from 700 to 750 °C. DTA and XRD evaluation revealed that the removal of Mn3Cr phase and formation of the single solid solution phase were the reason for the flow stress reduction. At the low deformation temperature (700°C) and the high strain rate (0.1 s-1), a partially recrystallized microstructure was observed; this was such that with increasing the temperature and decreasing the strain rate, a recrystallized microstructure was completed. Also, the relationships between flow stress, strain rate and deformation temperature were addressed by the Zener-Holloman parameter in the exponent type with the hot deformation activation energy of 301.07 KJ/mol. Finally, the constitutive equation was proposed for predicting the flow stress at various strain rates and temperatures.
Masumeh Mohammadi, Hamidreza Rezaei Ashtiani,
Volume 18, Issue 2 (6-2021)
Abstract
The hot deformation behavior of the heat-treated AA6061 and AA 6063 aluminum alloys by T6-1, T6-2 artificial aging treatment, and O annealing treatment were studied by compression testing over a temperature range of 350–550
and strain rates of 0.005-0.1 s
-1. It was observed that the flow stresses of the studied aluminum alloys treated by the T6-1 and T6-2 heat treatments were significantly higher than those of the O annealing treatment. Moreover, the stress-strain curves of the heat-treated alloys by the T6-1, T6-2, and O heat treatments demonstrated significant softening during deformation at the lowest strain rate under any of the deformation conditions. For several strains, the activation energy of hot deformation was specified and obtained to vary significantly with strain for the heat-treated alloys by the T6-1 and T6-2 treatments. The stress-strain data calculated from a linear equation, with strain-dependent parameters, shows a great fit with the experimental data for the heat-treated aluminum alloys.
Ata Abdi, Mehrdad Aghaie-Khafri,
Volume 19, Issue 1 (3-2022)
Abstract
Hot Workability and Processing Map of High Gd Content Mg-Gd-Zn-Zr-Nd Alloy Hot deformation behavior of homogenized Mg-4Sn binary alloy was studied using compression tests at the temperature range of 300-500
and strain rates of 0.001-1s
-1. The material showed typical single peak flow behavior followed by a steady state flow as a plateau, which is more evident at the high value of Zener-Hollomon parameter. Constitutive analysis showed that in spite of the original Johnson-Cook (J-C), conventional strain compensated Arrhenius model based on Sellars-McTegart model has a reasonable agreement with the experimental data. Moreover, the well-known hyperbolic sine function fits the experimental data for predicting of the peak stress with a fair degree of accuracy.
Hossein Momeni, Sasan Ranjbar Motlagh,
Volume 21, Issue 3 (9-2024)
Abstract
The present work deals with the hot deformation behavior of commercial Nb alloy C-103 and its microstructure evolution during uniaxial compression tests in the temperature range of 700-1100 °C and the strain rate range of 0.001-0.4 s-1. Strain rate sensitivity, calculated from the compression tests data, was almost constant and showed a negative value in the temperature range of 700-900 °C but increased significantly beyond 900 °C. Dynamic strain aging was found to have a predominant effect up to 900 °C, beyond which dynamic recovery and oxidation influenced the compressive properties. The microstructure of the deformed samples showed indications of dynamic recrystallization within the high strain rate sensitivity domain and features of flow instability in the regime of low strain rate sensitivity. The 950–1000 °C temperature range and strain rate range of 0.001-0.1 s-1 were suggested as suitable hot deformation conditions. The constitutive equation was established to describe the alloy's flow behavior, and the average activation energy for plastic flow was calculated to be 267 kJ/mol.
