Showing 109 results for Mo
M. Azarbarmas,
Volume 17, Issue 4 (12-2020)
Abstract
Mechanical properties of metals are substantially dependent on the microstructure, which can be controlled by thermo-mechanical parameters such as the temperature, strain and strain rate. Hence, understanding the microstructural evolution of alloys during the hot deformation is crucial for engineering the metal forming processes. The main objective of this work is to present an overview of Cellular Automaton (CA) modeling for predicting the microstructure of alloys during the dynamic recrystallization (DRX) phenomenon. In this review paper, first, overall descriptions about the DRX phenomenon and CA modeling were presented. Then, the CA modeling procedure was compared with similar methods. Meanwhile, related studies in the field of the DRX simulation by using the CA modeling were evaluated. Four main stages of the model were analyzed in terms of the “nucleation”, “growth”, “topological changes” and “texture evaluation” steps. Most important limitations including the calibration sensitivity, limitations in continuous DRX modeling, ignoring microstructural effects on the deformation behavior, limited applications and database as well as repeated results were discussed and then objective suggestions for the further development were provided. Finally, future prospects in CA modeling of DRX were presented in the last section.
Jafar Shafaghat, Ali Allahverdi,
Volume 18, Issue 1 (3-2021)
Abstract
Microscopic studies has shown that adjacent to the interface between cement paste and aggregate, there exists an area with high porosity and low binding compounds that is referred to as interfacial transition zone (ITZ). ITZ in concrete and mortar imposes a number of negative effects, including flexural and compressive strengths reduction and permeability enhancement. That’s why many research attempts have been devoted to limit ITZ and its negative effects. The present study investigates the possibility of utilizing fine Portland cement (PC) clinker as a reactive aggregate in mortar for the same purpose. For this, natural quartz sand in normal mortar (NM) was totally replaced with PC clinker of the same particle size distribution and the most important engineering properties of the new mortar referred to as Reactive Aggregate Mortar (RAM) were measured and compared with NM as control. The results of compressive strengths measurements represented 65% and 21% increases at curing ages of 7 and 90 days, respectively, for RAM compared to NM. Chloride penetration depth in RAM displayed reductions by about 33% and 26% after 14 and 28 days of exposure, respectively. The effect of PC clinker reactivity on the microstructure and size of ITZ was studied by using scanning electron microscopy.
Alireza Mirak,
Volume 18, Issue 2 (6-2021)
Abstract
In the present study, the early stages of the surface oxidation and fluoridation of liquid AZ91D and AM60B alloys under ultra-high purity (UHP) argon, dry air, and air mixed with two different protective fluorine-bearing gases were studied. The chemical composition, morphology and thickness of the surface films formed inside the trapped bubbles were characterized by SEM and EDS analyses. It is found that the molten AM60B alloy is more sensitive to impurities under UHP argon gas than AZ91D alloy. Under dry air atmosphere, the entire surface of molten AZ91D alloy is covered with an oxide layer and thinner thickness than the surface film formed on AM60B alloy which has a rough surface exhibiting granular growth in later stages of oxidation. The EDS analyses show that film chemistry is mainly composed of Mg, Al, and O elements. Under fluorine-bearing gas/air mixtures with either SF
6 or HFC-R134a at 3.5%vol., a fresh surface film formed with a flat and dense morphology of a uniform thickness composed of mixed Mg, F, Al, and O elements. It is observed that there is a lower O:F intensity ratio in the surface film formed on the molten AZ91D alloy under 1,1,1,2-tetra-fluoroethane (HFC-R134a) mixed with dry air compared to the AM60B alloy under both air/ R134a and air/SF
6 mixtures which shows a higher fluorine concentration in the surface film a leading to a better oxidation resistance
.
Sedigeh Mohamadnejad Zanjani, Ali Basti, Reza Ansari,
Volume 18, Issue 2 (6-2021)
Abstract
Phenomenological methods are more diagnostic tools than a predictor, so multi-crystalline material approaches based on their microstructures have been proposed during the last years. The purpose of this research is to review methods taking into account the effect of microstructures and texture deformation on predicting the behavior of sheet metals. These methods can be categorized into six general groups: Taylor-type models, crystal plasticity finite element methods, strain gradient methods, methods that consider dislocations, self-consistent methods, methods based on fast Fourier transform. This paper attempts to explain and compare these methods that have been used to forecasting forming limits or stress-strain curves.
Najwa Gouitaa, Lamcharfi Taj-Dine, Bouayad Lamfaddal, Abdi Farid, Mohamed Ounacer, Mohammed Sajieddine,
Volume 18, Issue 2 (6-2021)
Abstract
Prabhakar Kuppahalli, Ramaiah Keshavamurthy, Padmanathan Sriram, Ahobal Narayana,
Volume 18, Issue 2 (6-2021)
Abstract
The present investigation aims to synthesize RB031, RB032 manganese bronze alloys equivalent to HTB1 and HTB2 alloys with additions of silicon and to characterize them with the help of Microstructure and Mechanical properties. The methodology involves melting of alloy’s in a 300kg Coreless medium frequency induction furnace, casting them in Permanent and Shell moulds with optimum values of Zinc equivalent and retaining their high mechanical properties. The study includes the development and mechanical property measurements of the alloys synthesized. Characterization has been carried out using Optical Microscopy and Scanning Electron Microscopy with EDAX analysis for investiagtion of compositional variations and inquisition of hardness measurement & tensile properties. It is concluded from this work that RB032 alloy cast in Permanent moulds has superior hardness and tensile properties compared to Shell moulds and far exceeds that of NAB (AB2) alloys processed under similar conditions. Further, this investigation includes grain refinement by suitable Heat treatment studies to combat Hot Tearing since the strength is adequate enough with RB032 exhibiting higher hardness than other two alloys.
Rahida Wati Sharudin, Nik Salwani Md Azmi, Muhammad Shafiq Mat Shayuti, Masahiro Ohshima,
Volume 18, Issue 2 (6-2021)
Abstract
The control of silicone rubber’s viscoelastic properties namely loss factor, storage and loss moduli during crosslinking are crucial as its malleable behaviour changes differently under different conditions and affecting the final product. Hence, it becomes the objective of this study to investigate the rheological behaviour of silicone rubber cured under different formulation ratios with platinum catalysts and triethylamine, methanol & ethanolamine solvent. Measurement was conducted for the silicone rubber to crosslinker ratios of 2.5:7.5, 5:5, 7.5:2.5 and 10:1 at different elevated temperatures, and for the silicone rubber with triethylamine, methanol and ethanolamine at different angular frequencies. While the crossover of storage and modulus curve which signifies a gel point was not observed at higher ratios of platinum used across the temperature range of 25 – 100°C, it was found at 89°C and 95°C with the formulation ratios of 10:1 and 7.5:2.5, respectively. On the other hand, the crossover point was observed for silicone rubber at 100 s-1 for triethylamine, 3 s-1 and 100 s-1 for methanol, and 70 s-1 alongside 290 s-1 for ethanolamine. The presence of gel point indicates that crosslinking of silicone rubber successfully took place and this study proves that controlling the crosslinking behaviour was possible.
Arian Heidar Alaghband, Azam Moosavi, Saeid Baghshahi, Ali Khorsandzak,
Volume 18, Issue 3 (9-2021)
Abstract
Porous nanostructured SnO2 with a sheet-like morphology was synthesized through a simple green substrate-free gelatin-assisted calcination process using Tin tetracholoride pentahydrate as the SnO2 precursor and porcine gelatin as the template. Crystalline phase, morphology, microstructure, and optical characteristics of the as-prepared material were also investigated at different calcination temperatures using X-ray diffraction (XRD), Field emission scanning electron microscopy (FESEM), UV-visible absorption, and Photoluminescence spectroscopy (PL), respectively. XRD patterns of all the samples revealed the presence of a tetragonal crystalline structure with no other crystalline phases. Moreover, the synthesized hierarchical sheets assembled with nanoparticles displayed a large surface area and porous nanostructure. The calculated optical band gap energy varied from 2.62 to 2.87 eV depending on the calcination temperature. Finally, photoluminescence spectra indicated that the nanostructured SnO2 could exhibit an intensive UV-violet luminescence emission at 396 nm, with shoulders at 374, violet emission peaks at 405 and 414 nm, blue-green emission peak at 486 nm, green emission peak at 534 nm and orange emission peak at 628 nm.
Umarfarooq Maktedar Abdulkhadar, Patil Somalingana Shivakumar Gouda, Anil Shirahatti, Gonal Basavaraja Veeresh Kumar, Nagaraj Ramalingyya Banapurmath,
Volume 18, Issue 4 (12-2021)
Abstract
The energy release rate for delamination in a laminated composite is supposed to be the material property being considered as independent of non-material property variables. However, Mode I fracture toughness(GI) is found to vary with lamina arrangement, geometrical dimensions, and process-induced stresses. In this investigation, the influence of lamina stacking arrangement on process-induced stresses and their effects on GI of laminated composites are studied. Unidirectional (UD) ([0]16) and cross-ply ([902/06]s, [904/04]s and [906/02]s) Glass/ epoxy (GE) composites with the delamination plane at 0◦//0◦ were prepared by manual layup method and post-cured at 120 °C for 4 hours. GI of composite laminates were experimentally determined using a double cantilever beam(DCB) specimen as per ASTM D 5528. The slitting method was applied to determine the Process-induced stresses in GE laminates. The stacking sequence of laminas was found to have a noticeable effect on the state of residual stresses and GI of GE laminates. Residual stresses do not have much influence on the GI for delamination initiation, whereas GI for the crack propagation was found to increase with a gradual increase in compressive residual stresses in GE laminates.
Ata Abdi, Mehrdad Aghaie-Khafri,
Volume 19, Issue 1 (3-2022)
Abstract
Hot Workability and Processing Map of High Gd Content Mg-Gd-Zn-Zr-Nd Alloy Hot deformation behavior of homogenized Mg-4Sn binary alloy was studied using compression tests at the temperature range of 300-500
and strain rates of 0.001-1s
-1. The material showed typical single peak flow behavior followed by a steady state flow as a plateau, which is more evident at the high value of Zener-Hollomon parameter. Constitutive analysis showed that in spite of the original Johnson-Cook (J-C), conventional strain compensated Arrhenius model based on Sellars-McTegart model has a reasonable agreement with the experimental data. Moreover, the well-known hyperbolic sine function fits the experimental data for predicting of the peak stress with a fair degree of accuracy.
Hettal Souheila, Ouahab Abdelouahab, Rahmane Saad, Benmessaoud Ouarda, Kater Aicha, Sayad Mostefa,
Volume 19, Issue 1 (3-2022)
Abstract
Copper oxide thin layers were elaborated using the sol-gel dip-coating. The thickness effect on morphological, structural, optical and electrical properties was studied. Copper chloride dihydrate was used as precursor and dissolved into methanol. The scanning electron microscopy analysis results showed that there is continuity in formation of the clusters and the nuclei with the increase of number of the dips. X-ray diffractogram showed that all the films are polycrystalline cupric oxide CuO phase with monoclinic structure with grain size in the range of 30.72 - 26.58 nm. The obtained films are clear blackin appearance, which are confirmed by the optical transmittance spectra. The optical band gap energies of the deposited films vary from 3.80 to 3.70 eV. The electrical conductivity of the films decreases from 1.90.10-2 to 7.39.10-3 (Ω.cm)-1
Fiza Ur Rehman, Syeda Sohaila Naz, Muhammad Junaid Dar, Annum Malik, Maimoona Qindeel, Francesco Baino, Fazli Wahid, Abbas Rahdar, Saeeda Munir, Sara Qaisar, Kifayat Ullah Shah, Mahtab Razlansari,
Volume 19, Issue 2 (6-2022)
Abstract
Neoplastic cells have co-opted inflammatory receptors and signaling molecules that potentiate inflammation. Activated inflammatory pathways lead to neo-angiogenesis, lymph-angiogenesis, immunosuppression, tumor growth, proliferation and metastasis. This cancer-sustaining inflammation is a critical target to arrest cancer growth. Multiple drug resistance, high cost, low oral bioavailability and serious side effects have rendered conventional cytotoxic chemotherapeutics less impressive. The aim of this research was to achieve cancer debulking and proliferation prevention by limiting ‘cancer-sustaining’ tumor niche inflammation through non-conventional oral approach employing anti-inflammatory agents and avoiding conventional cytotoxic agents. Synergistic anti-inflammatory agents, i.e. celecoxib as selective COX-2 inhibitor and montelukast as cysteinyl leukotriene receptor antagonist, were selected. Silver nanoparticles (AgNPs) were used as nanocarriers because of their efficient synergistic anti-neoplastic effects and excellent oral drug delivery potential. Specifically, selected drugs were co-conjugated onto AgNPs. Synthesized nanoparticles were then surface-modified with poly(vinyl alcohol) to control particle size, avoid opsonization/preferred cellular uptake and improve dispersion. Surface plasmon resonance analysis, particle size analysis, DSC, TGA, XRD, FTIR and LIBS analysis confirmed the successful conjugation of drugs and efficient polymer coating with high loading efficiency. In-vitro, the nanoparticles manifested best and sustained release in moderately acidic (pH 4.5) milieu enabling passive tumor targeting potential. In-vivo, synthesized nanoparticles exhibited efficient dose-dependent anti-inflammatory activity reducing the dose up to 25-fold. The formulation also manifested hemo-compatibility, potent anti-denaturation activity and dose-dependent in-vitro and in-vivo anti-cancer potential against MCF-7 breast cancer and Hep-G2 liver cancer cell lines in both orthotopic and subcutaneous xenograft cancer models. The anti-inflammatory nanoparticles manifested tumor specific release potential exhibiting selective cytotoxicity at cancerous milieu with slightly acidic environment and activated inflammatory pathways. The formulation displayed impressive oral bioavailability, sustained release, negligible cytotoxicity against THLE-2 normal human hepatocytes, low toxicity (high LD50) and wide therapeutic window. Results suggest promise of developed nanomaterials as hemo-compatible, potent, cheaper, less-toxic oral anti-inflammatory and non-conventional anti-cancer agents.
Hannaneh Ghadirian, Hamid Golshahi, Sara Bahrami, Farhood Najafi, Allahyar Geramy, Soolmaz Heidari,
Volume 19, Issue 2 (6-2022)
Abstract
Quaternary ammonium compounds (QACs) are among the most commonly used antibacterial agents. The aim of this study was to synthesize a dimethacrylate monomer functionalized with a QAC and to study its effect on the properties of an orthodontic adhesive primer. Urethane dimethacrylate monomer functionalized with a QAC (UDMAQAC) was synthesized and then characterized by nuclear magnetic resonance spectroscopy (NMR) and Fourier transform infrared spectroscopy (FTIR). 5, 10, 15 and 20 wt% of UDMAQAC was added to an orthodontic adhesive primer (control group). FTIR analysis was used to measure the degree of conversion (DC). The bond strength of dental brackets was measured by shear bond strength (SBS) test and adhesive remaining index (ARI) was evaluated by stereomicroscope. Agar diffusion test and MTT assay were used to evaluate the antibacterial property and cell viability, respectively. Statistical analysis included one-way ANOVA with Tukey’s post hoc test and Kruskal-Wallis nonparametric test (P˂0.05). Although the obtained data did not show significant differences between the SBS and DC of different groups, but the highest values were obtained by adding 10 wt% monomer. Adding more than 10 wt% UDMAQAC resulted in significant increase in antibacterial property. The 15 and 20 wt% groups showed significantly lower cell viability
Behzad Pourghasemi, Vahid Abouei, Omid Bayat, Banafsheh Karbakhsh Ravari,
Volume 19, Issue 3 (9-2022)
Abstract
It has long been thought-provoking and challenging as well for researchers to design and produce a special low-modulus β titanium alloy such as Ti‐35Nb‐7Zr‐5Ta, representing optimal mechanical properties that is needed to successfully simulate bone tissue. In order to identify the key effects of processing pathways on the development of microstructure, Young’s modulus, and strength, a nominal Ti-35Nb-7Zr-5Ta alloy was made via casting, hot forging, homogenizing, cold rolling and finally annealing. Results from tensile test alongside microscopic and XRD analysis confirm the importance influence of processing method on fully β phase microstructure, low elastic modulus and high strength of the alloy. The specimen with post-deformation annealing at 500 °C demonstrated the Young’s modulus of 49.8 GPa, yield strength of 780 MPa and ultimate tensile strength of 890 MPa, all of which are incredibly close to that of bone, hence suitable for orthopedic implants. At temperature above 500 °C, a sharp fall was observed in the mechanical properties.
Mohammad Roostaei, Hossein Aghajani, Majid Abbasi, Behzad Abasht,
Volume 19, Issue 3 (9-2022)
Abstract
This study investigates the synthesis of Al/MoS2 nanocomposite coating by the electro spark deposition (ESD) method for its lubricating properties. ESD method was selected because it is a very easy, rapid, and cost-saving method and the resulting coating has a strong bonding with the substrate. As a substrate, a Ti-6Al-4V alloy sheet containing 6.12 % Al, 4.06 % V, 0.19% Fe, and 0.05 % Ni was used. For coating, an aluminum-molybdenum disulfide composite electrode in the form of a cylindrical rod was employed. Three frequencies of 5, 8, and 11 kHz, three current limits of 15, 25, and 35 amps, and three duty cycles of 50, 60, and 70% were used in the coating operation. AFM analysis was used to study the topography, morphology, and calculate roughness. The samples were then subjected to hardness tests. To determine the wear resistance of the samples, pin on disk tests were performed. XRD analysis was performed to identify the phases on the surface of the coated samples. SEM was used to examine the microstructure of the coating before and after wear testing, in order to determine the wear mechanism. The results indicated that the Al/MoS2 nanocomposite coating was synthesized on the substrate surface. The hardness of the reference sample is 353 Vickers, and that of the coated samples is about 200 Vickers. For the reference sample, the roughness was measured at 15.7 nm, and for the coated sample at 268.1 nm. As spark energy increased, the coefficient of friction increased by approximately 0.09. As spark energy increased, the wear rate increased by 27%. A significant increase in the Lancaster coefficient occurred around 5 joules of energy. According to the wear rate results, the sample with the lowest thickness wears 4% less than the sample with the highest thickness. The wear rate of sample 351170 is 78% lower than that of sample 150550.
Imtiaz Ali Soomro, Srinivasa Rao Pedapati, Mokhtar Awang, Afzal Ahmed Soomro, Mohammad Azad Alam, Bilawal Ahmed Bhayo,
Volume 19, Issue 4 (12-2022)
Abstract
This paper investigated the optimization, modelling and effect of welding parameters on the tensile shear load bearing capacity of double pulse resistance spot welded DP590 steel. Optimization of welding parameters was performed using the Taguchi design of experiment method. A relationship between input welding paramaters i.e., second pulse welding current, second pulse welding current time and first pulse holding time and output response i.e, tensile shear peak load was established using regression and neural network. Results showed that maximum average tensile shear peak load of 26.47 was achieved at optimum welding parameters i.e., second pulse welding current of 7.5 kA, second pulse welding time of 560 ms and first pulse holding time of 400 ms. It was also found that the ANN model predicted the tensile shear load with higher accuracy than the regression model.
Ali Ebrahimpour, Amir Mostafapour, Naeimeh Hagi,
Volume 20, Issue 1 (3-2023)
Abstract
In this research, the effect of RSW parameters including current intensity, welding time and welding force (coded by A, B and C) on the radius, thickness and area of the nugget and the radius of the HAZ of TRIP steel joints was investigated by DOE and RSM. A 3D coupled thermal-electrical-structural FEM was used to model RSW. To validate the FE model, two TRIP steel sheets were welded experimentally. During welding, the temperature was measured and the results were compared with the FE results and a good agreement was obtained. The boundaries of the welding zones were determined according to the critical temperatures and the responses in all samples were calculated. Using analysis of variance, direct, quadratic and interaction effects of parameters on the responses were studied and a mathematical model was obtained for each response. The direct linear effects of all parameters on all responses were significant. But among the interaction effects, the effect of B×C on the nugget radius, the effect of A×B on the nugget thickness, the effect of A×B on the nugget area and the effects of A×B and B×C on the HAZ radius were significant. Also, current intensity had the greatest effect on all responses.
Mohammad Abankar, Hossein Arabi, Mohammad Taghi Salehi, Majid Abbasi,
Volume 20, Issue 1 (3-2023)
Abstract
The aims of this research were to evaluate the effects of different thermomechanical treatments on the microstructure and investigate some of the mechanical properties of a TWIP steel rich in Mn & Al. So, a block of a TWIP steel with nominal composition Fe-17.5Mn-1.36Al-0.8C was cast and then subjected to hot rolling followed by cold rolling and heat treatment. Cold rolling was performed before heat treatment in order to reduce the grain size and improve the tensile and fatigue properties. X-ray diffraction technique was used before and after the heat treatment to evaluate the possibility of any phase formation. No sign of martensitic transformation after cold deformation was observed. However, by increasing the amount of cold deformation, the number of mechanical twins and slip band increased resulted to an increase in hardness and strength. The best tensile and fatigue result were obtained after 47% thickness reduction and annealing at 715˚C for 10 min. Under these conditions, the mean grain size reduced from 138 to 9 μm resulted to an increase in yield strength from 395 to 510 MPa, and the fatigue life improvement from the mean life of 10200 for the cast sample to 21500 cycles for the treated sample, when these samples underwent fatigue tests at a stress range of 650 MPa and R=0. In addition, the diameter and depth of dimples in fracture surfaces decreased by reducing the grain size but the fracture mode was remained ductile and adequate plastic deformation occurred before failure.
Mohammad Alipour,
Volume 20, Issue 1 (3-2023)
Abstract
The effect of Strain-Induced Melt-Activated (SIMA) Process, ultrasonic treatment (UST) and Al-5Ti-1B refiner on the microstructure and globularity of Al–15%Mg2Si composite was studied. Deformation of 25% were used. After deformation the samples were heated at 560, 580 and 595 °C for 5, 10, 20 and 40 min. The composite was treated with different amounts of the Ti concentrations and ultrasonic treatment with different power. Microstructural study was carried out on the alloy. It was observed that SIMA process, ultrasonic treatment and Al-5Ti-1B refiner has caused the globular morphology of Mg2Si particles. The results showed that for the desired microstructures of the alloy during SIMA process, the optimum temperature and time are 595 °C and 20 min respectively. Optimum amount of Ti refiner is 1 wt.% and power for UST is 1800W. After applying the SIMA process, Al-5Ti-1B master alloy and ultrasonic treatment, the strength and engagement have increased. This means that tensile strength increases from 251 MPa to 303 MPa and elongation percentage improves from 2.1 to 3.4, respectively.
Ali Hasanzade Salmasi, Mahban Zarei, Shadab Safarzadeh Khosroshahi, Soolmaz Heidari, Farhood Najafi, Mojtaba Ghomayshi, Katayoun Lesani,
Volume 20, Issue 3 (9-2023)
Abstract
Amorphous calcium phosphate (ACP) which is a transient phase in natural bio-mineralization process has recently gained the spotlight. This study aimed to assess the effect of incorporation of nano-ACP (NACP) in a dental adhesive with/without surface treatment with silane coupling agent on bond strength. NACP was synthesized by the wet chemical precipitation technique. To characterize the structure of NACP, X-ray diffraction, scanning electron microscopy and energy dispersive X-ray spectroscopy were used. Forty molars were randomized into 4 groups of 10. The teeth were restored with composite resin and the bonding agent (one of the four groups). Adper Single Bond 2 was used as the control group. In 4wt% NACP group, NACP fillers were added to the bonding agent. In 0.4wt% and 4wt% SNACP groups, silanized NACP fillers were added to the bonding agent. Finally, the mode of failure of specimens was determined. Data were analyzed by one-way ANOVA and Tukey's post-hoc tests. P<0.05 was considered statistically significant. Addition of 4wt% non-silanized NACP decreased the bond strength compared with the control group (P<0.05). The bond strength of the groups with silanized fillers was not significantly different from that of the control group. Addition of silanized NACP to dental adhesive had no significant adverse effect on bond strength, which is a promising finding to pave the way for the synthesis of bonding agents containing bioactive fillers.
